TEL: 0871-317180
Contact us
TEL: 0871-317180

Interior decoration of the most common paint problems

&Nbsp;    decoration painting in peeling paint may surface too smooth sake. Original quality of paint or powder coating is light (with untreated color coating), the new paint will not adhere on the surface on prison. Or possibly wood rot or rust metal, there is peeling because of poor paint quality. Small areas of peeling paint, start with fine sandpaper and PuTTY on a wipe, paint primer, then paint. All large areas of peeling paint must be removed, again brushing. &Nbsp;

paint bubbling  

first of all, foam punctured, if water come out, that is, the infiltration of moisture behind or under the paint layer, scorched by the Sun, the water evaporates into vapor, will paint up into bubbles. At this time, use a hot air gun to remove blistered paint, let the wood dry and paint primer, then paint over the entire patch on the surface again. If the bubbles in the water, may be cracking the wood grain, with a small amount of air, scorched by the Sun, air expands, paint up. Faced with this situation, first scrape off bubbling paint and resin fillers filled cracks, paint on the back, or no fill, after you scrape off the paint, coat microporous paint directly.  


this happens mostly with chemical paint remover or hot air gun will paint out, then painted. If faults too small when sanding block or wet or dry sandpaper available water, grinding the paint to break on the surface polished after, spread PuTTY, paint primer, and paint again.  


paint a brush too thick, which will result in stream {HotTag} drips. While paint is not yet dry, with small brush paint brush, and if the paint was dry, you want to stay dry, the paint surfaces sanded smooth with fine sandpaper, brush the surface clean, then wipe clean with a damp cloth, and then external coats of paint, careful not to brush too thick.


paint stains on the surface for many reasons. For example, latex paint water dissolved substances on the walls and rust paint, use steel wool to clean the wall surface will produce rust spots, within the walls of underground pipe leak stains and other.

to prevent stains, you can brush a layer of aluminum powder primer, if the stain has occurred, you can remove stains latex paint, brush after the primer layer with aluminium powder, coated all over again.  

moldy color  

this problem occurs on the surface of wet paint, such as condensation on the glass or metal surfaces often have a dark brown stain. Available fungicides, according to manual instructions handling mouldy parts, after treating the fungus killed, cleaned the surface, and then paint again.  


because no primer or primer and paint not directly on the paint, resulting in lost gloss varnish is absorbed by the wood. Poor paint quality is also a factor. Use wet or dry sandpaper rub off old paint, brush sanding dust, wipe the surfaces with a clean damp cloth, dry, brush on paint all over again. Pay special attention to is, in an environment of very low temperatures painted, paint film dries, may lose its lustre.  

paint film  

usually because the first paint is not dry brush arising out of the second. Lower solvent affects the top layer of paint in the paint to make it wrinkle. The chemical removal of mercury available agents or heat to remove wrinkled coating, painting again. Remember, be sure to wait for the first time after the paint dried, only on a second time.

paint rough  

newly painted surface rough, usually with a paint brush is not clean or by the surrounding environment. Or it could be paint mixed with patent leather, in use prior to settling and filtering, or stained with dust when the paint is dry. To prevent these problems, you must use a clean paint brush and paint bucket. Old paint before use, be sure to use a paint filter filter paper or a clean nylon stockings. In addition, the painted surfaces when paint is dry use covers or cardboard hidden to prevent stained with dirt. If coarse finish, waiting for them to dry, after the smooth, wipe with wet or dry sandpaper, brush again with paint. Pay special attention to paint must be clean.  

  painted wood surfaces appear dark spots;

wood Festival in front of a painting might not be sealed, after Sun drying, wood heating, resin exudation resulting from wood Festival. Used a scraper to paint, then with fine sandpaper to reveal after the wood, paint will seal the wood section until dry, then paint.

paint does not dry  

poor ventilation or temperature is too low, the paint will dry more slowly. It is possible to open all doors and Windows to promote ventilation, or put a heater in the room to increase the room temperature. If they still cannot solve the problem, it may be coated surface greasy. Use chemical paint remover or heat to remove paint, wipe the surface completely, and then paint again.  

bug   on the paint surface;

the bug picked off before the paint is dry, then gently with a brush dipped a little oil patch surface. If the paint has begun to dry, while it will be film hardens completely, then wipe off the bugs, do not make surfaces to collapse

Copyright, All rights reserved  E-mail: